ariens model 924046 manual

The Ariens Model 924046 is a high-performance snow blower designed for residential use, featuring a powerful engine, durable steel construction, multiple speed settings, electric start capability, adjustable chute control, and easy maneuverability. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Steel auger and impeller, Electric start system, Adjustable skid shoes, 6-speed transmission, Headlight, Chute control handle, and Drift cutters.

Feature	Description
Engine	Powerful 4-cycle engine with electric start capability
Clearing Width	24-inch clearing path for efficient snow removal
Intake Height	21-inch intake height for handling deep snow
Transmission	6 forward speeds and 2 reverse speeds
Chute Control	Adjustable chute with 200-degree rotation
Auger	Durable steel auger with serrated edges
Skid Shoes	Adjustable for proper clearance on various surfaces
Headlight	Built-in headlight for visibility in low-light conditions
Drift Cutters	Side cutters for handling deep snow drifts
Tires	Heavy-duty tires with aggressive tread pattern

Assembly Instructions

Unpack and inspect all contents. Assembly requires basic tools.

1. Handle Assembly: Attach upper handle to lower handle using provided bolts.
2. Chute Assembly: Install chute assembly and secure with mounting hardware.
3. Control Cables: Connect throttle control and chute control cables.
4. Skid Shoes: Install adjustable skid shoes on both sides.
5. Drift Cutters: Attach drift cutters to both sides of the housing.
6. Headlight: Connect headlight wiring according to diagram.

WARNING! Ensure all bolts are properly tightened. Keep hands clear of moving parts during assembly.

First-Time Setup

Complete assembly before first use. Prepare machine for operation.

1. Add Engine Oil: Fill with recommended SAE 5W-30 oil to proper level.
2. Add Fuel: Use fresh unleaded gasoline with ethanol content under 10%.
3. Check Tire Pressure: Inflate tires to 15 PSI.
4. Adjust Skid Shoes: Set clearance appropriate for your surface.
5. Test Controls: Verify all controls operate smoothly before starting engine.

CAUTION! Perform setup in well-ventilated area away from ignition sources.

Specifications

• Model Number: 924046
• Engine Type: 4-cycle, overhead valve
• Engine Displacement: 208cc
• Starting System: Electric start with backup recoil
• Clearing Width: 24 inches
• Intake Height: 21 inches
• Discharge Distance: Up to 40 feet
• Transmission: 6 forward speeds, 2 reverse speeds
• Chute Rotation: 200 degrees
• Chute Control: Crank handle adjustment
• Tire Size: 15 x 5.00-6
• Weight: 215 pounds

Controls and Settings

Main controls located on handle panel. Chute controls on right side of machine.

Handle Controls: Electric start button, Throttle control, Choke, Drive control lever, Auger control lever, Headlight switch.

Chute Controls: Rotation crank (200-degree adjustment), Deflector control lever.

Adjustments: Skid shoes (height adjustment), Drift cutters (side clearance), Handle height (multiple positions).

Operating Procedures

Always wear appropriate safety gear. Clear area of obstacles before operation.

1. Starting: Engage choke, turn key to start position (electric) or pull recoil starter.
2. Warm-up: Allow engine to warm up for 2-3 minutes before engaging auger.
3. Engaging Auger: Pull auger control lever to engage snow clearing mechanism.
4. Select Speed: Choose appropriate forward speed based on snow conditions.
5. Direct Discharge: Use chute crank to direct snow where desired.
6. Shutting Down: Release auger control, engage parking brake, turn off engine.

Tip: Overlap each pass by several inches for complete clearing.

Maintenance Schedule

Regular maintenance ensures optimal performance and longevity.

Maintenance Item	Frequency	Procedure
Check Engine Oil	Before each use	Verify oil level is between marks on dipstick
Change Engine Oil	After first 5 hours, then every 50 hours	Drain old oil, replace with fresh SAE 5W-30
Check Spark Plug	Every 25 hours	Clean and gap to 0.030 inches
Lubricate Auger Shaft	Every 25 hours	Apply grease to zerks on auger shaft
Check Drive Belts	Every 50 hours	Inspect for wear and proper tension
Check Shear Bolts	Before each season	Replace if damaged or sheared

Storage Guidelines

Proper storage prevents damage and prepares machine for next season.

1. Fuel System: Add fuel stabilizer and run engine for 5 minutes, or drain fuel completely.
2. Engine: Change oil if due, remove spark plug and add teaspoon of oil to cylinder.
3. Auger Housing: Clean thoroughly and spray with silicone lubricant.
4. Tires: Inflate to proper pressure and store off ground if possible.
5. Cover: Use weather-resistant cover to protect from elements.

CAUTION! Store in dry location away from children and pets.

Safety Information

Read and understand all safety instructions before operation.

• Always wear eye protection and sturdy footwear.
• Keep hands and feet away from all moving parts.
• Never attempt to clear clog while engine is running.
• Keep children and pets away from operating area.
• Operate only in well-lit conditions or with headlight on.
• Never operate on slopes greater than 15 degrees.
• Use only approved replacement parts.

DANGER! Risk of serious injury or death. Follow all safety precautions.

Warranty Details

Ariens provides limited warranty coverage for residential use.

Warranty Period: 3-year limited warranty from date of purchase.

Coverage: Defects in materials and workmanship under normal use.

Exclusions: Normal wear, improper maintenance, commercial use, neglect or abuse.

Registration: Register product within 30 days of purchase at www.ariens.com.

Service: Contact authorized Ariens service dealer for warranty claims.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	Fuel issues, spark plug, safety switch	Check fuel level and quality, inspect spark plug, ensure all safety switches engaged
Electric start not working	Battery, connections, key switch	Check battery charge, clean connections, test key switch
Auger won't engage	Shear bolts, drive belt, control cable	Check shear bolts for damage, inspect drive belt, adjust control cable
Poor snow discharge	Worn auger, impeller clearance, speed	Inspect auger paddles, adjust impeller clearance, reduce operating speed
Machine vibrates excessively	Loose parts, unbalanced auger, damaged components	Tighten all bolts, check auger balance, inspect for damage
Loss of power	Fuel filter, air filter, carburetor	Replace fuel filter, clean air filter, service carburetor

Technical Support: 1-800-678-5443; www.ariens.com