The Ariens Model 921022 is a high-performance snowblower designed for reliable winter operation. This parts manual provides detailed information, diagrams, and part numbers for all major components including the engine, auger assembly, drive system, controls, and chassis. Below are key sections for identification, assembly groups, exploded views, part numbers, ordering information, and maintenance.
Locate the model and serial number plate on the frame. Key specifications for the Ariens Model 921022.
| Feature | Description |
|---|---|
| Model Number | 921022 |
| Engine Type | 4-Cycle, OHV |
| Engine Displacement | 208cc (Approx.) |
| Clearing Width | 24 inches |
| Intake Height | 21 inches |
| Drive System | 2-Stage, Gear-Driven |
| Auger Material | Steel with Rubber Paddles |
| Chassis Type | Steel Frame |
| Controls | Handlebars with Levers |
| Weight | Approx. 210 lbs |
Always follow safety procedures when servicing or operating the snowblower.
WARNING! Failure to follow safety instructions can result in serious injury or damage to the equipment. Never operate with missing or damaged guards.
Refer to the following assembly groups for part identification. Each group includes an exploded view diagram (reference number in manual).
NOTE: Diagrams are not included in this HTML version. Refer to the PDF manual for visual references.
Critical components for snow intake and discharge.
Auger Shaft: Steel shaft with hex ends. Auger Paddles: Rubber or steel blades (left and right). Shear Pins/Bolts: 1/4" x 1-1/4" (replace if broken). Auger Bearings: Sealed ball bearings (2 required). Impeller: 12" diameter steel fan. Impeller Shear Bolts: Protect gear case. Skid Shoes: Adjustable wear bars (2). Scraper Bar: Located at housing bottom.
Components that provide traction and auger/impeller power.
Tip: Always check belt tension and wear before each season.
Operator interface and structural frame parts.
WARNING! Ensure all control cables are properly adjusted and secured for safe operation.
Standard hardware used throughout the assembly. Most are Grade 5 or better.
| Description | Size/Type | Qty (Typical) |
|---|---|---|
| Hex Bolt | 1/4"-20 x 3/4" | Various |
| Lock Nut | 1/4"-20 Nylock | Various |
| Flat Washer | 1/4" | Various |
| Shear Bolt | 1/4" x 1-1/4" | 4-6 |
| Cotter Pin | 1/8" x 1" | 2 |
| Spring Pin | 3/16" x 1" | 2 |
| Control Cable Clip | -- | 4 |
Common part numbers for Ariens Model 921022. Verify with your dealer.
Auger Paddle (Left): 015-XXXXX-00 | Auger Paddle (Right): 015-XXXXX-01 | Shear Pin Kit: 035-XXXXX | Drive Belt: 045-XXXXX | Auger Belt: 045-XXXXX | Skid Shoe: 025-XXXXX | Spark Plug: 030-XXXXX | Air Filter: 040-XXXXX | Control Cable (Drive): 050-XXXXX | Control Cable (Auger): 050-XXXXX
NOTE: XXXX denotes variable digits. Always use the exact part number from your specific diagram.
Contact an authorized Ariens dealer for genuine parts.
CAUTION! Use of non-genuine parts may void warranty and affect performance and safety.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Engine won't start | Fuel, spark, compression | Check fuel, spark plug, recoil starter, carburetor. |
| Auger doesn't turn | Shear pins, belt, cable | Inspect/replace shear pins; check auger belt and engagement cable. |
| No forward/reverse drive | Drive belt, friction disc, cable | Adjust/replace drive belt; inspect friction disc and control cable. |
| Excessive vibration | Loose parts, damaged auger | Tighten all bolts; check for bent auger shaft or paddles. |
| Poor snow discharge | Worn paddles, impeller, belt | Replace worn paddles/impeller; check impeller belt tension. |
Maintenance: Change engine oil annually, check belts and cables pre-season, lubricate pivot points, store with empty fuel tank.
Service: For technical support or dealer location, visit www.ariens.com or contact 1-800-XXX-XXXX.