Ariens Deluxe 24 Service Manual

The Ariens Deluxe 24 is a 24-inch two-stage snow thrower designed for residential snow removal. It features a 208cc Ariens AX engine, electric start, 6 forward speeds and 2 reverse speeds, power steering, heated hand grips, LED headlights, and a durable steel auger and impeller. This manual covers safety procedures, maintenance schedules, troubleshooting, and repair instructions for optimal performance and longevity. Below are key sections for operation, maintenance, specifications, and troubleshooting.

1. Safety Information 2. Specifications 3. Controls and Operation 4. Maintenance Schedule 5. Engine Service 6. Drive System 7. Auger and Impeller 8. Electrical System 9. Storage & Off-Season Care 10. Troubleshooting 11. Parts List & Diagrams

Safety Information

Always read and understand all safety instructions before operating or servicing the snow thrower.

Hazard	Precaution
Rotating Auger/Impeller	Never clear clogged chute with engine running. Always use clean-out tool.
Fuel Handling	Refuel outdoors only when engine is cool. Use fresh, stabilized gasoline.
Electric Start	Keep extension cord clear of auger and discharge chute during starting.
Thrown Objects	Clear area of debris before operation. Keep bystanders and pets away.
Carbon Monoxide	Never operate engine in enclosed or partially enclosed spaces.
Maintenance Safety	Disconnect spark plug wire before performing any maintenance or repairs.

Specifications

Model: Ariens Deluxe 24
Clearing Width: 24 inches
Engine: 208cc Ariens AX Engine (4-cycle, OHV)
Starting System: Electric Start (120V) with Recoil Backup
Drive System: 6 Forward Speeds, 2 Reverse Speeds, Power Steering
Auger: 12-inch diameter, serrated steel
Impeller: 12-inch diameter, 4-blade steel
Chute Control: 180-degree rotation, crank adjustment
Features: Heated Hand Grips, LED Headlights, Skid Shoes
Fuel Capacity: 1.0 gallon
Oil Capacity: 20 oz. (SAE 5W-30 synthetic recommended)

Controls and Operation

Key components: Engine controls, drive control lever, auger control lever, chute control crank, skid shoe adjusters.

Starting Procedure:

Check oil and fuel levels.
Open fuel valve (if equipped).
Set choke to "ON" for cold starts.
For Electric Start: Plug in cord, turn key to "ON", press start button.
For Recoil Start: Pull starter cord firmly.
Move choke to "OFF" as engine warms.

Operation: Engage drive lever slowly. Engage auger lever to begin snow removal. Adjust discharge direction with chute crank. Adjust clearing height with skid shoes.

WARNING! Never operate without proper safety equipment. Keep hands and feet away from moving parts.

Maintenance Schedule

Regular maintenance ensures reliability and extends machine life.

Interval	Task
Before Each Use	Check fasteners, inspect auger/impeller for damage, check skid shoes.
First 5 Hours	Change engine oil (break-in period).
Every 25 Hours or Season	Change engine oil, check/spark plug, inspect drive belt.
Every 50 Hours or Season	Change oil, replace spark plug, inspect/clean carburetor air filter.
Every 100 Hours	Replace fuel filter, inspect auger shear pins/belts, lubricate controls.
End of Season	Drain fuel or add stabilizer, run engine dry, clean entire unit, lubricate.

Engine Service

208cc Ariens AX Engine maintenance procedures.

Oil Change: Run engine to warm oil. Remove drain plug, drain into pan. Refill with 20 oz. SAE 5W-30 synthetic.
Spark Plug: Disconnect wire. Clean area, remove plug. Gap to 0.030 inches. Install new plug (Champion RC12YC or equivalent).
Air Filter: Remove cover. Clean foam pre-filter with soap/water. Replace paper element if dirty.
Fuel System: Replace inline fuel filter annually. Clean fuel tank sediment cup if equipped.

CAUTION! Engine is hot during/after operation. Allow to cool before servicing.

Drive System

6-speed transmission with friction disc drive and power steering.

Drive Belt Inspection: Check for cracks, fraying, or glazing. Replace if worn.
Belt Replacement: Release tension, remove belt guard, slip off old belt. Route new belt per diagram. Adjust tension.
Traction Adjustment: Adjust drive control cable for full engagement/disengagement.
Power Steering: Ensure steering rods are lubricated and linkages are tight.

Tip: Keep drive system free of ice and packed snow buildup.

Auger and Impeller

Steel auger and impeller assembly with shear bolt protection.

Shear Bolt Replacement: If auger stops turning, inspect shear bolts. Remove broken bolt, install new 1/4" x 1-1/2" grade 2 bolt with nut. Do not use harder bolt.
Auger Belt: Inspect for wear. Replace if cracked. Adjust tension per manual.
Lubrication: Lubricate auger shaft bearings at start of season.
Impeller Clearance: Check impeller to housing clearance (1/8 inch max). Adjust if needed.

WARNING! Always disconnect spark plug before working on auger/impeller.

Electrical System

Electric start, headlights, and heated grips.

Electric Start: Check battery charge in starter. Test outlet and extension cord. Inspect wiring for damage.
LED Headlights: Replace bulb by removing lens cover. Use part # 035-12300.
Heated Grips: Test switch and connections. Replace heating element if inoperative.
Key Switch: Test continuity. Replace if start circuit fails.

Storage & Off-Season Care

Proper storage prevents corrosion and fuel system issues.

Run engine to burn off fuel in carburetor OR add fuel stabilizer and run for 5 minutes.
Change engine oil.
Clean entire machine thoroughly. Touch up any scratches with paint to prevent rust.
Lubricate all pivot points, cables, and chute mechanism.
Store in a clean, dry place. Cover unit.

CAUTION! Never store with gasoline in tank without stabilizer for more than 30 days.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	No fuel, bad spark, choke setting	Check fuel valve, spark plug, use correct choke procedure.
Electric start fails	Dead outlet, bad cord, starter fault	Test outlet/cord, check starter motor connections.
Loss of power	Clogged fuel filter, dirty air filter	Replace fuel filter, clean/replace air filter.
Auger won't turn	Shear bolt broken, belt loose/broken	Replace shear bolt(s), inspect/tighten/replace auger belt.
Poor traction	Drive belt worn, tension incorrect	Inspect/replace drive belt, adjust cable tension.
Uneven discharge	Worn skid shoes, impeller damage	Adjust/replace skid shoes, inspect impeller blades.
Excessive vibration	Loose hardware, damaged auger	Tighten all bolts/nuts, inspect auger for bends.

Technical Support: 1-800-678-9443; www.ariens.com

Parts List & Diagrams

Refer to official Ariens Deluxe 24 Parts Manual (PDF 035-12345) for complete illustrated parts breakdown and part numbers for engine, drive system, auger housing, controls, and hardware. Available at www.ariens.com/en-us/manuals.