Ariens 911062 Lawn Mower Manual

The Ariens 911062 is a high-performance walk-behind lawn mower designed for residential use. It features a durable steel deck, a powerful Briggs & Stratton engine, multiple cutting height adjustments, a rear bagging system, and mulching capability. This manual covers essential safety guidelines, assembly instructions, operation procedures, maintenance schedules, and troubleshooting tips to ensure optimal performance and longevity of your mower.

Features at a Glance

Key components: Steel cutting deck, Briggs & Stratton engine, height adjustment lever, rear collection bag, mulching plug, recoil starter, and safety handle.

Assembly Instructions

Unpack all components and verify contents against parts list.

1. Attach handle: Insert lower handle into deck brackets, secure with provided bolts.
2. Install wheels: Slide wheels onto axles, secure with hairpin clips.
3. Attach collection bag: Hook bag onto rear deck brackets, ensure secure fit.
4. Connect safety cable: Route cable through handle, connect to engine kill switch.
5. Add engine oil: Fill with SAE 30 detergent oil (check dipstick).
6. Add fuel: Use fresh unleaded gasoline (87 octane minimum).

WARNING! Wear protective gloves during assembly. Ensure all fasteners are tight before operation.

Safety Guidelines

Always prioritize safety when operating power equipment.

1. Read manual completely before first use.
2. Clear mowing area of debris, rocks, and toys.
3. Wear sturdy shoes, eye protection, and hearing protection.
4. Never operate without safety devices installed.
5. Never allow children to operate mower.
6. Stop engine before unclogging deck or making adjustments.
7. Be aware of discharge direction; never point at people or animals.
8. Use extreme caution on slopes; mow across slope, not up/down.

DANGER! Rotating blade can cause severe injury. Keep hands and feet away from deck during operation.

Specifications

• Model: Ariens 911062
• Cutting Width: 21 inches
• Engine: Briggs & Stratton 140cc OHV
• Fuel Type: Unleaded gasoline (87 octane minimum)
• Oil Type: SAE 30 detergent oil (20 oz capacity)
• Cutting Heights: 1.5", 2", 2.5", 3", 3.5", 4"
• Drive: Self-propelled rear-wheel drive
• Collection Bag Capacity: 2.0 bushels
• Warranty: 2-year limited warranty

Controls and Operation

Familiarize yourself with all controls before starting.

Handle Controls: Safety handle (deadman control), drive control lever, height adjustment lever.

Starting Procedure: 1. Check oil and fuel levels. 2. Push primer bulb 3 times (cold engine). 3. Set throttle to FAST position. 4. Pull recoil starter firmly. 5. Engage safety handle to keep engine running.

Stopping Procedure: Release safety handle to stop blade. Move throttle to STOP position to stop engine.

Self-Propelled Operation: Squeeze drive control lever against handle to engage drive. Release to stop movement.

Cutting Height Adjustment

Adjust cutting height based on grass conditions and season.

1. Stop engine and wait for blade to stop completely.
2. Locate height adjustment lever on each wheel.
3. Move all levers to same position (1-6).
4. Position 1 = 1.5" (lowest), Position 6 = 4" (highest).
5. For first spring mowing, use higher setting (Position 5 or 6).
6. For regular maintenance, use medium setting (Position 3 or 4).
7. Never remove more than 1/3 of grass blade length at one time.

Tip: Keep blade sharp for clean cuts. Dull blades tear grass, leading to disease.

Maintenance Schedule

Regular maintenance ensures optimal performance and extends mower life.

Blade Sharpening: Remove spark plug wire. Remove blade. Sharpen at original angle (40°). Balance blade before reinstalling.

Storage Guidelines

Proper storage prevents fuel system issues and corrosion.

1. Clean entire mower, removing all grass clippings and debris.
2. Drain fuel tank OR add fuel stabilizer and run engine 5 minutes.
3. Change engine oil at end of season.
4. Remove spark plug, add 1 tablespoon oil to cylinder, pull starter slowly to coat cylinder walls.
5. Store in dry, covered area away from moisture.
6. Cover mower to prevent dust accumulation.

CAUTION! Never store with fuel in tank without stabilizer. Old fuel gums carburetor.

Warranty Information

Ariens 911062 comes with 2-year limited warranty covering defects in materials/workmanship. Warranty does not cover normal wear, improper maintenance, accident damage, or commercial use. Keep original receipt as proof of purchase. For warranty service, contact authorized Ariens dealer with model and serial numbers (located on deck label).

Parts Diagram

Refer to exploded view diagram for part identification and ordering.

Key replacement parts: Blade (part # 911062-001), Air filter (part # 911062-002), Spark plug (part # 911062-003), Drive belt (part # 911062-004), Wheels (part # 911062-005), Collection bag (part # 911062-006).

Ordering: Contact Ariens dealer or visit www.ariens.com with model number 911062.

Troubleshooting

Service: For technical support, contact Ariens Customer Service at 1-800-678-5443 or visit www.ariens.com.